Skip to content
PCB maintenance spray

Electronic Card (PCB) Maintenance Spray

Cleans boards and contacts, displaces moisture, evaporates fast and leaves no residue.

Technical information

Product typeAerosol cleaning and maintenance spray for electronic boards
UseCleaning boards, connectors, contacts and relays; moisture displacement
DryingEvaporates quickly, air-dries
ResidueLeaves no residue or oily film
PenetrationLow surface tension, high capillary action
Material compatibilityMost plastics, metals, rubbers and insulating materials
Dielectric strengthHigh; value in the product TDS
Permanent protectionNone; apply a conformal coating for lasting protection

Drying time, viscosity and pack sizes are given in the product TDS.

Electronic card maintenance spray is a service spray that cleans printed circuit boards, connectors and contacts, displaces surface moisture and evaporates quickly without leaving residue. Orhun Kimya makes it to its own formulation at its plant in Beylikdüzü, Istanbul. Its low surface tension and high capillary action let it creep between pins, into narrow gaps and connector housings, and spread over the surface.

Water ingress, humidity, condensation and corrosion are among the most common causes of electrical and electronic faults. The spray is used to reduce the leakage currents, poor contacts and oxidation they cause, and to protect the service life and reliability of the equipment. It is not a permanent coating: it cleans and dries the board and readies it to go back into service.

Where is it used?

  • Routine maintenance of control, automation and PLC boards,
  • Cleaning connector, terminal, relay and switch contacts,
  • Drying panels and boards exposed to moisture or condensation before power-up,
  • Removing dust and dirt from boards after repair and soldering,
  • Quick field service without dismantling the unit.

Properties

  • High purity: developed for sensitive equipment; leaves no oily film or residue.
  • Fast penetration and evaporation: works into tight gaps and air-dries quickly.
  • Moisture displacement: drives off surface moisture and condensation, reducing corrosion risk.
  • High dielectric strength: does not create a conductive path across the circuit during application.
  • Material compatibility: compatible with most plastics, metals, rubbers and insulating materials.

How to apply

  1. Switch off the equipment and wait for capacitors to discharge.
  2. Remove heavy dust with a soft brush or dry compressed air.
  3. Shake the can and spray in short bursts from close range.
  4. Work dirty areas with a soft antistatic brush and let the liquid carry the dirt away.
  5. Wait until the spray has fully evaporated, then power the unit up.

If lasting moisture protection is needed after drying, an electronic card insulating varnish (conformal coating) can be applied.

Maintenance spray or insulating varnish?

They do different jobs. The maintenance spray removes existing dirt and moisture and leaves the board clean and dry; nothing remains once it evaporates. An insulating varnish is applied to a clean, dry board and forms a permanent film once cured. The right order is cleaning and drying first, then coating if needed. Varnishing a dirty or damp board traps the moisture and dirt under the coating.

What to watch out for

  • The spray cleans and removes moisture; it does not insulate the board permanently. In constantly damp or vibrating environments, potting the board with polyurethane or epoxy resin is the better solution.
  • On sensitive or painted plastics, test first on a small hidden area.
  • The aerosol propellant may be flammable: do not spray onto live circuits, hot surfaces or near open flames; ventilate the area.
  • Do not leave the can in direct sun or above 50 °C.

Common mistakes

  • Spraying without isolating the power,
  • Switching on before the spray has fully evaporated,
  • Trying to dissolve heavy grease and dirt with spray alone; mechanical cleaning comes first,
  • Treating the maintenance spray as winding insulation; for motor and transformer windings use motor insulating spray or winding varnish.

For readings that drop because of moisture, see the insulation resistance guide; for our other aerosols, see spray products. For packaging and technical data, write to us via the form or WhatsApp.

Questions

What does PCB maintenance spray do?

It removes dirt, dust and moisture from boards, connectors and contacts, then evaporates without residue. It reduces leakage-current and poor-contact faults caused by humidity, condensation and corrosion.

Does the spray leave a permanent protective layer?

No. It cleans and evaporates and leaves no lasting film. For permanent moisture protection, apply an electronic card insulating varnish once the board is dry.

Can it be used on live circuits?

No. Switch the power off first and restart only after the spray has fully evaporated. The aerosol propellant may be flammable.

How long does it take to dry?

It evaporates quickly; the exact time depends on temperature and the amount applied and is given in the product TDS. Ask for it via the form or WhatsApp.

Will it damage plastic parts?

It is compatible with most plastics, metals, rubbers and insulating materials. On sensitive or painted plastics, test on a small hidden area first.

Can it be used to insulate a motor winding?

No. This spray is for cleaning and maintenance. Use F-class motor insulating spray or winding varnish to insulate windings.

Orhun Kimya sprays for electronic boardsAn Orhun Kimya insulating varnish can held in an open handEmpty tins seen from above in a box, with an Orhun Kimya can on top

More in this group

Related reading

Let's choose your varnish

Tell us the motor type, the operating temperature and how you apply varnish; we will send the right product, its TDS and a price.

+90 532 358 15 64
ali@orhunkimya.com.tr

Nothing you type is stored on our server; your message opens directly in WhatsApp or your email app.